Le informazioni sugli articoli di fonte ISI sono coperte da copyright

Per ulteriori informazioni selezionare i riferimenti di interesse.

1. Traverso, A; Massardo, AF
   Thermoeconomic analysis of mixed gas-steam cycles
   APPLIED THERMAL ENGINEERING
   
   A. Traverso e A.F. Massardo, "Thermoeconomic analysis of mixed gas-steam cycles", APPL TH ENG, 22(1), 2002, pp. 1-21
2. Hammons, TJ
   Mitigating climate change with renewable and high-efficiency generation
   ELECTRIC POWER COMPONENTS AND SYSTEMS
   
   T.J. Hammons, "Mitigating climate change with renewable and high-efficiency generation", EL POW CO S, 29(9), 2001, pp. 849-865
3. De Zilwa, SRN; Emiris, I; Uhm, JH; Whitelaw, JH
   Combustion of premixed methane and air in ducts
   PROCEEDINGS OF THE ROYAL SOCIETY OF LONDON SERIES A-MATHEMATICAL PHYSICAL AND ENGINEERING SCIENCES
   
   S.R.N. De Zilwa et al., "Combustion of premixed methane and air in ducts", P ROY SOC A, 457(2012), 2001, pp. 1915-1949
4. Rosler, J; Baker, M; Volgmann, M
   Stress state and failure mechanisms of thermal barrier coatings: Role of creep in thermally grown oxide
   ACTA MATERIALIA
   
   J. Rosler et al., "Stress state and failure mechanisms of thermal barrier coatings: Role of creep in thermally grown oxide", ACT MATER, 49(18), 2001, pp. 3659-3670
5. Kolev, N; Schaber, K; Kolev, D
   A new type of a gas-steam turbine cycle with increased efficiency
   APPLIED THERMAL ENGINEERING
   
   N. Kolev et al., "A new type of a gas-steam turbine cycle with increased efficiency", APPL TH ENG, 21(4), 2001, pp. 391-405
6. De Paepe, M; Dick, E
   Technological and economical analysis of water recovery in steam injected gas turbines
   APPLIED THERMAL ENGINEERING
   
   M. De Paepe e E. Dick, "Technological and economical analysis of water recovery in steam injected gas turbines", APPL TH ENG, 21(2), 2001, pp. 135-156
7. Bassily, AM
   Effects of evaporative inlet and aftercooling on the recuperated gas turbine cycle
   APPLIED THERMAL ENGINEERING
   
   A.M. Bassily, "Effects of evaporative inlet and aftercooling on the recuperated gas turbine cycle", APPL TH ENG, 21(18), 2001, pp. 1875-1890
8. Sharma, NY; Datta, A; Som, SK
   Influences of spray and operating parameters on penetration of vaporizing fuel droplets in a gas turbine combustor
   APPLIED THERMAL ENGINEERING
   
   N.Y. Sharma et al., "Influences of spray and operating parameters on penetration of vaporizing fuel droplets in a gas turbine combustor", APPL TH ENG, 21(17), 2001, pp. 1755-1768
9. Cooper, DA
   Exhaust emissions from high speed passenger ferries
   ATMOSPHERIC ENVIRONMENT
   
   D.A. Cooper, "Exhaust emissions from high speed passenger ferries", ATMOS ENVIR, 35(24), 2001, pp. 4189-4200
10. Shlyannikov, VN; Iltchenko, BV; Stapanov, NV
    Fracture analysis of turbine disks and computational-experimental background of the operational decisions
    ENGINEERING FAILURE ANALYSIS
    
    V.N. Shlyannikov et al., "Fracture analysis of turbine disks and computational-experimental background of the operational decisions", ENG FAIL AN, 8(5), 2001, pp. 461-475
11. Yuri, I; Hisamatsu, T; Etori, Y; Yamamoto, T
    Degradation of silicon carbide in combustion gas flow at high temperature and high speed
    JSME INTERNATIONAL JOURNAL SERIES A-SOLID MECHANICS AND MATERIAL ENGINEERING
    
    I. Yuri et al., "Degradation of silicon carbide in combustion gas flow at high temperature and high speed", JSME A, 44(4), 2001, pp. 520-527
12. Cho, HH; Rhee, DH; Kim, BG
    Enhancement of film cooling performance using a shaped film cooling hole with compound angle injection
    JSME INTERNATIONAL JOURNAL SERIES B-FLUIDS AND THERMAL ENGINEERING
    
    H.H. Cho et al., "Enhancement of film cooling performance using a shaped film cooling hole with compound angle injection", JSME I J B, 44(1), 2001, pp. 99-110
13. Abdallah, H; Harvey, S
    Thermodynamic analysis of chemically recuperated gas turbines
    INTERNATIONAL JOURNAL OF THERMAL SCIENCES
    
    H. Abdallah e S. Harvey, "Thermodynamic analysis of chemically recuperated gas turbines", INT J TH SC, 40(4), 2001, pp. 372-384
14. Lee, AS; Lee, YS
    Rotordynamic characteristics of an APU gas turbine rotor-bearing system having a tie shaft
    KSME INTERNATIONAL JOURNAL
    
    A.S. Lee e Y.S. Lee, "Rotordynamic characteristics of an APU gas turbine rotor-bearing system having a tie shaft", KSME INT J, 15(2), 2001, pp. 152-159
15. Moon, BY; Kang, BS; Kim, BS
    Dynamic analysis of harmonically excited non-linear structure system usingharmonic balance method
    KSME INTERNATIONAL JOURNAL
    
    B.Y. Moon et al., "Dynamic analysis of harmonically excited non-linear structure system usingharmonic balance method", KSME INT J, 15(11), 2001, pp. 1507-1516
16. Stricker, J; Goldman, Y; Borodyanski, G
    Thermochemical protection of high temperature materials
    JOURNAL OF ENHANCED HEAT TRANSFER
    
    J. Stricker et al., "Thermochemical protection of high temperature materials", J ENHANC H, 8(4), 2001, pp. 231-241
17. Lvova, E; Norsworthy, D
    Influence of service-induced microstructural changes on the aging kineticsof rejuvenated Ni-based superalloy gas turbine blades
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
    
    E. Lvova e D. Norsworthy, "Influence of service-induced microstructural changes on the aging kineticsof rejuvenated Ni-based superalloy gas turbine blades", J MAT ENG P, 10(3), 2001, pp. 299-312
18. Tanaka, S; Sugimoto, S; Li, JF; Watanabe, R; Esashi, M
    Silicon carbide micro-reaction-sintering using micromachined silicon molds
    JOURNAL OF MICROELECTROMECHANICAL SYSTEMS
    
    S. Tanaka et al., "Silicon carbide micro-reaction-sintering using micromachined silicon molds", J MICROEL S, 10(1), 2001, pp. 55-61
19. Salehi, M; Heshmat, H
    Performance of a complaint foil seal in a small gas turbine engine simulator employing a hybrid foil/ball bearing support system
    TRIBOLOGY TRANSACTIONS
    
    M. Salehi e H. Heshmat, "Performance of a complaint foil seal in a small gas turbine engine simulator employing a hybrid foil/ball bearing support system", TRIBOL T, 44(3), 2001, pp. 458-464
20. Wada, K; Yan, L; Takahashi, M; Takaishi, K; Furukawa, T
    Degradation of gas turbine blade materials in integrated coal-gasificationcombined cycle plant
    MATERIALS AT HIGH TEMPERATURES
    
    K. Wada et al., "Degradation of gas turbine blade materials in integrated coal-gasificationcombined cycle plant", MATER HIGH, 18(2), 2001, pp. 131-138
21. Zedda, M; Singh, R
    Neural-network-based sensor validation for gas turbine test bed analysis
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART I-JOURNAL OF SYSTEMS AND CONTROL ENGINEERING
    
    M. Zedda e R. Singh, "Neural-network-based sensor validation for gas turbine test bed analysis", P I MEC E I, 215(I1), 2001, pp. 47-56
22. Carcasci, C; Cormacchione, NAC
    Part load operating strategies for gas turbines in district heating applications
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    C. Carcasci e N.A.C. Cormacchione, "Part load operating strategies for gas turbines in district heating applications", P I MEC E A, 215(A5), 2001, pp. 529-544
23. Bassily, AM
    Performance improvements of the intercooled reheat regenerative gas turbine cycles using indirect evaporative cooling of the inlet air and evaporative cooling of the compressor discharge
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    A.M. Bassily, "Performance improvements of the intercooled reheat regenerative gas turbine cycles using indirect evaporative cooling of the inlet air and evaporative cooling of the compressor discharge", P I MEC E A, 215(A5), 2001, pp. 545-557
24. Bharani, S; Singh, SN; Agrawal, DP
    Flow characteristics in the liner of a reverse-flow gas turbine combustor
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    S. Bharani et al., "Flow characteristics in the liner of a reverse-flow gas turbine combustor", P I MEC E A, 215(A4), 2001, pp. 443-451
25. Guha, A
    Performance and optimization of gas turbines with real gas effects
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    A. Guha, "Performance and optimization of gas turbines with real gas effects", P I MEC E A, 215(A4), 2001, pp. 507-512
26. Kim, JH; Kim, TS; Ro, ST
    Analysis of the dynamic behaviour of regenerative gas turbines
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    J.H. Kim et al., "Analysis of the dynamic behaviour of regenerative gas turbines", P I MEC E A, 215(A3), 2001, pp. 339-346
27. Guha, A
    An efficient generic method for calculating the properties of combustion products
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    A. Guha, "An efficient generic method for calculating the properties of combustion products", P I MEC E A, 215(A3), 2001, pp. 375-387
28. Mathioudakis, K; Stamatis, A; Tsalavoutas, A; Aretakis, N
    Performance analysis of industrial gas turbines for engine condition monitoring
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    K. Mathioudakis et al., "Performance analysis of industrial gas turbines for engine condition monitoring", P I MEC E A, 215(A2), 2001, pp. 173-184
29. Woolhouse, RJ; Tippetts, JR; Beck, SBM
    A comparison of the experimental and computational modelling of the fluidic turn-up vortex amplifier at full and zero swirl conditions
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE
    
    R.J. Woolhouse et al., "A comparison of the experimental and computational modelling of the fluidic turn-up vortex amplifier at full and zero swirl conditions", P I MEC E C, 215(C8), 2001, pp. 893-903
30. Thevenin, PO; Ersson, AG; Kusar, HMJ; Menon, PG; Jaras, SG
    Deactivation of high temperature combustion catalysts
    APPLIED CATALYSIS A-GENERAL
    
    P.O. Thevenin et al., "Deactivation of high temperature combustion catalysts", APP CATAL A, 212(1-2), 2001, pp. 189-197
31. Ma, XQ; Takemoto, M
    Quantitative acoustic emission analysis of plasma sprayed thermal barrier coatings subjected to thermal shock tests
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
    
    X.Q. Ma e M. Takemoto, "Quantitative acoustic emission analysis of plasma sprayed thermal barrier coatings subjected to thermal shock tests", MAT SCI E A, 308(1-2), 2001, pp. 101-110
32. Han, MH; Ahn, YS; Kim, SK; Shon, SK; Kang, SK; Cho, SJ
    Synthesis of manganese substituted hexaaluminate and its fabrication into monolithic honeycombs for catalytic combustion
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
    
    M.H. Han et al., "Synthesis of manganese substituted hexaaluminate and its fabrication into monolithic honeycombs for catalytic combustion", MAT SCI E A, 302(2), 2001, pp. 286-293
33. Booth, C; Mcdonald, JR; Mcarthur, SDJ
    Forecasting and prediction applications in the field of power engineering
    JOURNAL OF INTELLIGENT & ROBOTIC SYSTEMS
    
    C. Booth et al., "Forecasting and prediction applications in the field of power engineering", J INTEL ROB, 31(1-3), 2001, pp. 159-184
34. Canu, P
    Simulation and interpretation of catalytic combustion experimental data
    CATALYSIS TODAY
    
    P. Canu, "Simulation and interpretation of catalytic combustion experimental data", CATAL TODAY, 64(3-4), 2001, pp. 239-252
35. Yokoyama, F; Haneishi, T; Masuko, M
    Correlation between change in kinematic viscosity and change in total acidnumber due to oxidative deterioration of oil
    JOURNAL OF JAPANESE SOCIETY OF TRIBOLOGISTS
    
    F. Yokoyama et al., "Correlation between change in kinematic viscosity and change in total acidnumber due to oxidative deterioration of oil", J JPN SOC T, 46(9), 2001, pp. 733-736
36. Richards, GA; McMillian, MM; Gemmen, RS; Rogers, WA; Cully, SR
    Issues for low-emission, fuel-flexible power systems
    PROGRESS IN ENERGY AND COMBUSTION SCIENCE
    
    G.A. Richards et al., "Issues for low-emission, fuel-flexible power systems", PROG ENERG, 27(2), 2001, pp. 141-169
37. Roy, N; Godiwalla, KM; Chaudhuri, S; Ray, AK
    Simulation of bond coat properties in thermal barrier coatings during bending
    HIGH TEMPERATURE MATERIALS AND PROCESSES
    
    N. Roy et al., "Simulation of bond coat properties in thermal barrier coatings during bending", HIGH TEMP M, 20(2), 2001, pp. 103-116
38. Ahn, T; Ryu, S
    Fuzzy PNN algorithm and its application to nonlinear processes
    INTERNATIONAL JOURNAL OF GENERAL SYSTEMS
    
    T. Ahn e S. Ryu, "Fuzzy PNN algorithm and its application to nonlinear processes", INT J GEN S, 30(4), 2001, pp. 463-478
39. Chen, LG; Zheng, JL; Sun, FR; Wu, C
    Power density optimization for an irreversible regenerated closed Brayton cycle
    PHYSICA SCRIPTA
    
    L.G. Chen et al., "Power density optimization for an irreversible regenerated closed Brayton cycle", PHYS SCR, 64(3), 2001, pp. 184-191
40. Taniguchi, H; Tezuka, J; Iwata, M; Arai, N
    Major auxiliary equipment needs for the world energy network project
    ENERGY CONVERSION AND MANAGEMENT
    
    H. Taniguchi et al., "Major auxiliary equipment needs for the world energy network project", ENERG CONV, 42(15-17), 2001, pp. 1831-1837
41. Kachi, T; Kato, Y; Ushigome, N; Arai, N
    Evaluation of the coating layer formed on the substrate of C/C composites
    ENERGY CONVERSION AND MANAGEMENT
    
    T. Kachi et al., "Evaluation of the coating layer formed on the substrate of C/C composites", ENERG CONV, 42(15-17), 2001, pp. 1963-1975
42. Ohji, T
    High-temperature reliability of advanced ceramics
    JOURNAL OF ENERGY RESOURCES TECHNOLOGY-TRANSACTIONS OF THE ASME
    
    T. Ohji, "High-temperature reliability of advanced ceramics", J ENERG RES, 123(1), 2001, pp. 64-69
43. Takemoto, M; Chiba, A; Fukao, T
    A method of determining the advanced angle of square-wave currents in a bearingless switched reluctance motor
    IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS
    
    M. Takemoto et al., "A method of determining the advanced angle of square-wave currents in a bearingless switched reluctance motor", IEEE IND AP, 37(6), 2001, pp. 1702-1709
44. Croce, F; Delfino, B; Fazzini, PA; Massucco, S; Morini, A; Silvestro, F; Sivieri, M
    Operation and management of the electric system for industrial plants: An expert system prototype for load-shedding operator assistance
    IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS
    
    F. Croce et al., "Operation and management of the electric system for industrial plants: An expert system prototype for load-shedding operator assistance", IEEE IND AP, 37(3), 2001, pp. 701-708
45. Paduano, JD; Greitzer, EM; Epstein, AH
    Compression system stability and active control
    ANNUAL REVIEW OF FLUID MECHANICS
    
    J.D. Paduano et al., "Compression system stability and active control", ANN R FLUID, 33, 2001, pp. 491-517
46. Chen, LG; Zheng, JL; Sun, FR; Wu, C
    Power density analysis and optimization of a regenerated closed variable-temperature heat reservoir Brayton cycle
    JOURNAL OF PHYSICS D-APPLIED PHYSICS
    
    L.G. Chen et al., "Power density analysis and optimization of a regenerated closed variable-temperature heat reservoir Brayton cycle", J PHYS D, 34(11), 2001, pp. 1727-1739
47. Oo, AN; Ching, CY
    Effect of turbulence with different vortical structures on stagnation region heat transfer
    JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME
    
    A.N. Oo e C.Y. Ching, "Effect of turbulence with different vortical structures on stagnation region heat transfer", J HEAT TRAN, 123(4), 2001, pp. 665-674
48. Zhao, DQ; Ohno, Y; Furuhata, T; Yamashita, H; Arai, N; Hisazumi, Y
    Combustion technology in a novel gas turbine system with steam injection and two-stage combustion
    JOURNAL OF CHEMICAL ENGINEERING OF JAPAN
    
    D.Q. Zhao et al., "Combustion technology in a novel gas turbine system with steam injection and two-stage combustion", J CHEM EN J, 34(9), 2001, pp. 1159-1164
49. Marceau, E; Lauron-Pernot, H; Che, M
    Influence of the metallic precursor and of the catalytic reaction on the activity and evolution of Pt(Cl)delta-Al2O3 catalysts in the total oxidationof methane
    JOURNAL OF CATALYSIS
    
    E. Marceau et al., "Influence of the metallic precursor and of the catalytic reaction on the activity and evolution of Pt(Cl)delta-Al2O3 catalysts in the total oxidationof methane", J CATALYSIS, 197(2), 2001, pp. 394-405
50. Zhou, YC; Hashida, T
    Coupled effects of temperature gradient and oxidation on thermal stress inthermal barrier coating system
    INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES
    
    Y.C. Zhou e T. Hashida, "Coupled effects of temperature gradient and oxidation on thermal stress inthermal barrier coating system", INT J SOL S, 38(24-25), 2001, pp. 4235-4264
51. Ciavarella, M; Demelio, G
    A review of analytical aspects of fretting fatigue, with extension to damage parameters, and application to dovetail joints
    INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES
    
    M. Ciavarella e G. Demelio, "A review of analytical aspects of fretting fatigue, with extension to damage parameters, and application to dovetail joints", INT J SOL S, 38(10-13), 2001, pp. 1791-1811
52. Griffin, GJ; Wood, DG
    Non-adiabatic catalytic combustion at a fin surface involving heat extraction from the fin edge
    COMBUSTION AND FLAME
    
    G.J. Griffin e D.G. Wood, "Non-adiabatic catalytic combustion at a fin surface involving heat extraction from the fin edge", COMB FLAME, 125(4), 2001, pp. 1230-1238
53. Cominos, V; Gavriilidis, A
    Theoretical investigation of axially non-uniform catalytic monoliths for methane combustion
    CHEMICAL ENGINEERING SCIENCE
    
    V. Cominos e A. Gavriilidis, "Theoretical investigation of axially non-uniform catalytic monoliths for methane combustion", CHEM ENG SC, 56(11), 2001, pp. 3455-3468
54. Ishiyama, S; Muto, Y; Tanihira, M; Ogata, K; Kamito, Y; Igari, T
    Development of the compact heat exchanger for the HTGR, (I) fabrication ofthe ultra fine off-set fin
    JOURNAL OF THE ATOMIC ENERGY SOCIETY OF JAPAN
    
    S. Ishiyama et al., "Development of the compact heat exchanger for the HTGR, (I) fabrication ofthe ultra fine off-set fin", J ATOM E S, 43(6), 2001, pp. 603-611
55. Schluter, JU; Schonfeld, T
    LES of jets in cross flow and its application to a gas turbine burner
    FLOW TURBULENCE AND COMBUSTION
    
    J.U. Schluter e T. Schonfeld, "LES of jets in cross flow and its application to a gas turbine burner", FLOW TURB C, 65(2), 2000, pp. 177-203
56. Tzimas, E; Mullejans, H; Peteves, SD; Bressers, J; Stamm, W
    Failure of thermal barrier coating systems under cyclic thermomechanical loading
    ACTA MATERIALIA
    
    E. Tzimas et al., "Failure of thermal barrier coating systems under cyclic thermomechanical loading", ACT MATER, 48(18-19), 2000, pp. 4699-4707
57. Kakatsios, XK; Krikkis, RN; Arapis, DK
    Modelling and simulation of a temperature compensation device in a fuel control unit
    APPLIED THERMAL ENGINEERING
    
    X.K. Kakatsios et al., "Modelling and simulation of a temperature compensation device in a fuel control unit", APPL TH ENG, 20(4), 2000, pp. 371-385
58. Pilavachi, PA
    Power generation with gas turbine systems and combined heat and power
    APPLIED THERMAL ENGINEERING
    
    P.A. Pilavachi, "Power generation with gas turbine systems and combined heat and power", APPL TH ENG, 20(15-16), 2000, pp. 1421-1429
59. Kim, TS; Lee, DK; Ro, ST
    Analysis of thermal stress evolution in the steam drum during start-up of a heat recovery steam generator
    APPLIED THERMAL ENGINEERING
    
    T.S. Kim et al., "Analysis of thermal stress evolution in the steam drum during start-up of a heat recovery steam generator", APPL TH ENG, 20(11), 2000, pp. 977-992
60. Xi, NS; Zhong, PD; Huang, HQ; Yan, H; Tao, CH
    Failure investigation of blade and disk in first stage compressor
    ENGINEERING FAILURE ANALYSIS
    
    N.S. Xi et al., "Failure investigation of blade and disk in first stage compressor", ENG FAIL AN, 7(6), 2000, pp. 385-392
61. Bulloch, JH; Callagy, AG
    Assessment of a premature failure in a gas turbine part
    ENGINEERING FAILURE ANALYSIS
    
    J.H. Bulloch e A.G. Callagy, "Assessment of a premature failure in a gas turbine part", ENG FAIL AN, 7(6), 2000, pp. 411-426
62. Matsuda, H; Otomo, F; Inomata, A; Fukuyama, Y; Ishii, J
    Pressure loss characteristics in rotating coolant passages of gas turbine
    JSME INTERNATIONAL JOURNAL SERIES B-FLUIDS AND THERMAL ENGINEERING
    
    H. Matsuda et al., "Pressure loss characteristics in rotating coolant passages of gas turbine", JSME I J B, 43(4), 2000, pp. 614-621
63. Moliere, M
    Stationary gas turbines and primary energies: A review of fuel influence on energy and combustion performances
    INTERNATIONAL JOURNAL OF THERMAL SCIENCES
    
    M. Moliere, "Stationary gas turbines and primary energies: A review of fuel influence on energy and combustion performances", INT J TH SC, 39(2), 2000, pp. 141-172
64. Facchini, B; Ferrara, G; Innocenti, L
    Blade cooling improvement for heavy duty gas turbine: the air coolant temperature reduction and the introduction of steam and mixed steam/air cooling
    INTERNATIONAL JOURNAL OF THERMAL SCIENCES
    
    B. Facchini et al., "Blade cooling improvement for heavy duty gas turbine: the air coolant temperature reduction and the introduction of steam and mixed steam/air cooling", INT J TH SC, 39(1), 2000, pp. 74-84
65. Meier, UE; Wolff-Gassmann, D; Stricker, W
    LIF imaging and 2D temperature mapping in a model combustor at elevated pressure
    AEROSPACE SCIENCE AND TECHNOLOGY
    
    U.E. Meier et al., "LIF imaging and 2D temperature mapping in a model combustor at elevated pressure", AEROSP SC T, 4(6), 2000, pp. 403-414
66. Haynes, JA; Ferber, MK; Porter, WD
    Thermal cycling behavior of plasmsa-sprayed thermal barrier coatings with various MCrAlX bond coats
    JOURNAL OF THERMAL SPRAY TECHNOLOGY
    
    J.A. Haynes et al., "Thermal cycling behavior of plasmsa-sprayed thermal barrier coatings with various MCrAlX bond coats", J THERM SPR, 9(1), 2000, pp. 38-48
67. Mehra, A; Zhang, X; Ayon, AA; Waitz, IA; Schmidt, MA; Spadaccini, CM
    A six-wafer combustion system for a silicon micro gas turbine engine
    JOURNAL OF MICROELECTROMECHANICAL SYSTEMS
    
    A. Mehra et al., "A six-wafer combustion system for a silicon micro gas turbine engine", J MICROEL S, 9(4), 2000, pp. 517-527
68. Kauffman, RE; Feng, AS; Karasek, KR
    Coke formation from aircraft engine oils: Part II - Effects of oil formulation and surface composition
    TRIBOLOGY TRANSACTIONS
    
    R.E. Kauffman et al., "Coke formation from aircraft engine oils: Part II - Effects of oil formulation and surface composition", TRIBOL T, 43(4), 2000, pp. 677-680
69. Kauffman, RE; Feng, A; Karasek, KR
    Coke formation from aircraft turbine engine oils: Part I - Deposit analysis and development of laboratory oil coking test
    TRIBOLOGY TRANSACTIONS
    
    R.E. Kauffman et al., "Coke formation from aircraft turbine engine oils: Part I - Deposit analysis and development of laboratory oil coking test", TRIBOL T, 43(4), 2000, pp. 823-829
70. Boucher, ME; Chaala, A; Pakdel, H; Roy, C
    Bio-oils obtained by vacuum pyrolysis of softwood bark as a liquid fuel for gas turbines. Part II: Stability and ageing of bio-oil and its blends with methanol and a pyrolytic aqueous phase
    BIOMASS & BIOENERGY
    
    M.E. Boucher et al., "Bio-oils obtained by vacuum pyrolysis of softwood bark as a liquid fuel for gas turbines. Part II: Stability and ageing of bio-oil and its blends with methanol and a pyrolytic aqueous phase", BIO BIOENER, 19(5), 2000, pp. 351-361
71. Juste, GL; Monfort, JJS
    Preliminary test on combustion of wood derived fast pyrolysis oils in a gas turbine combustor
    BIOMASS & BIOENERGY
    
    G.L. Juste e J.J.S. Monfort, "Preliminary test on combustion of wood derived fast pyrolysis oils in a gas turbine combustor", BIO BIOENER, 19(2), 2000, pp. 119-128
72. Bouhanek, K; Adesanya, OA; Stott, FH; Skeldon, P; Lees, DG; Wood, GC
    Isothermal and thermal cyclic oxidation behaviour of thermal barrier coatings: Pt aluminide bond coats
    MATERIALS AT HIGH TEMPERATURES
    
    K. Bouhanek et al., "Isothermal and thermal cyclic oxidation behaviour of thermal barrier coatings: Pt aluminide bond coats", MATER HIGH, 17(2), 2000, pp. 185-196
73. Simms, NJ; Oakey, JE; Nicholls, JR
    Development and application of a methodology for the measurement of corrosion and erosion damage in laboratory, burner rig and plant environments
    MATERIALS AT HIGH TEMPERATURES
    
    N.J. Simms et al., "Development and application of a methodology for the measurement of corrosion and erosion damage in laboratory, burner rig and plant environments", MATER HIGH, 17(2), 2000, pp. 355-362
74. Kikstra, JF; Verkooijen, AHM
    Conceptual design for the energy conversion system of a nuclear gas turbine cogeneration plant
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    J.F. Kikstra e A.H.M. Verkooijen, "Conceptual design for the energy conversion system of a nuclear gas turbine cogeneration plant", P I MEC E A, 214(A5), 2000, pp. 401-411
75. Turner, AB; Davies, SJ; Childs, PRN; Harvey, CG; Millward, JA
    Development of a novel gas turbine driven centrifugal compressor
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    A.B. Turner et al., "Development of a novel gas turbine driven centrifugal compressor", P I MEC E A, 214(A5), 2000, pp. 423-437
76. Alkabie, H
    Design methods of the ABB ALSTOM POWER gas turbine dry low emission combustion system
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    H. Alkabie, "Design methods of the ABB ALSTOM POWER gas turbine dry low emission combustion system", P I MEC E A, 214(A4), 2000, pp. 293-315
77. Schlatter, JC
    Ultra-low NOx via catalytic combustion
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    J.C. Schlatter, "Ultra-low NOx via catalytic combustion", P I MEC E A, 214(A4), 2000, pp. 377-383
78. Wood, MI
    Gas turbine hot section components: the challenge of 'residual life' assessment
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    M.I. Wood, "Gas turbine hot section components: the challenge of 'residual life' assessment", P I MEC E A, 214(A3), 2000, pp. 193-201
79. Ritchey, I; Fisher, EH; Agnew, GD
    Water spray cooling of gas turbine cycles
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    I. Ritchey et al., "Water spray cooling of gas turbine cycles", P I MEC E A, 214(A3), 2000, pp. 203-211
80. Camporeale, SM; Fortunato, B; Dumas, A
    Dynamic modelling of recuperative gas turbines
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    S.M. Camporeale et al., "Dynamic modelling of recuperative gas turbines", P I MEC E A, 214(A3), 2000, pp. 213-225
81. Huang, YC; Hung, CI; Chen, CK
    Exergy analysis for a combined system of steam-injected gas turbine cogeneration and multiple-effect evaporation
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY
    
    Y.C. Huang et al., "Exergy analysis for a combined system of steam-injected gas turbine cogeneration and multiple-effect evaporation", P I MEC E A, 214(A1), 2000, pp. 61-73
82. Zielinski, M; Ziller, G
    Noncontact vibration measurements on compressor rotor blades
    MEASUREMENT SCIENCE & TECHNOLOGY
    
    M. Zielinski e G. Ziller, "Noncontact vibration measurements on compressor rotor blades", MEAS SCI T, 11(7), 2000, pp. 847-856
83. McDonell, VG; Samuelsen, GS
    Measurement of fuel mixing and transport processes in gas turbine combustion
    MEASUREMENT SCIENCE & TECHNOLOGY
    
    V.G. McDonell e G.S. Samuelsen, "Measurement of fuel mixing and transport processes in gas turbine combustion", MEAS SCI T, 11(7), 2000, pp. 870-886
84. Ireland, PT; Jones, TV
    Liquid crystal measurements of heat transfer and surface shear stress
    MEASUREMENT SCIENCE & TECHNOLOGY
    
    P.T. Ireland e T.V. Jones, "Liquid crystal measurements of heat transfer and surface shear stress", MEAS SCI T, 11(7), 2000, pp. 969-986
85. Aunapu, NV; Volino, RJ; Flack, KA
    Surface flow visualization of a scaled-up turbine blade passage
    MEASUREMENT SCIENCE & TECHNOLOGY
    
    N.V. Aunapu et al., "Surface flow visualization of a scaled-up turbine blade passage", MEAS SCI T, 11(7), 2000, pp. 987-991
86. Ligrani, P
    Flow visualization and flow tracking as applied to turbine components in gas turbine engines
    MEASUREMENT SCIENCE & TECHNOLOGY
    
    P. Ligrani, "Flow visualization and flow tracking as applied to turbine components in gas turbine engines", MEAS SCI T, 11(7), 2000, pp. 992-1006
87. Piccini, E; Guo, SM; Jones, TV
    The development of a new direct-heat-flux gauge for heat-transfer facilities
    MEASUREMENT SCIENCE & TECHNOLOGY
    
    E. Piccini et al., "The development of a new direct-heat-flux gauge for heat-transfer facilities", MEAS SCI T, 11(4), 2000, pp. 342-349
88. Holmquist, M; Lundberg, R; Sudre, O; Razzell, AG; Molliex, L; Benoit, J; Adlerborn, J
    Alumina/alumina composite with a porous zirconia interphase - Processing, properties and component testing
    JOURNAL OF THE EUROPEAN CERAMIC SOCIETY
    
    M. Holmquist et al., "Alumina/alumina composite with a porous zirconia interphase - Processing, properties and component testing", J EUR CERAM, 20(5), 2000, pp. 599-606
89. Lindstedt, RP
    The modelling of direct chemical kinetic effects in turbulent flames
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART G-JOURNAL OF AEROSPACE ENGINEERING
    
    R.P. Lindstedt, "The modelling of direct chemical kinetic effects in turbulent flames", P I MEC E G, 214(G3), 2000, pp. 177-189
90. Lewins, JD
    The ideal gas Joule cycle at maximum specific work
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE
    
    J.D. Lewins, "The ideal gas Joule cycle at maximum specific work", P I MEC E C, 214(12), 2000, pp. 1545-1551
91. Organ, AJ
    Two centuries of the thermal regenerator
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE
    
    A.J. Organ, "Two centuries of the thermal regenerator", P I MEC E C, 214(1), 2000, pp. 269-288
92. Ruffles, PC
    The future of aircraft propulsion
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE
    
    P.C. Ruffles, "The future of aircraft propulsion", P I MEC E C, 214(1), 2000, pp. 289-305
93. Vyas, JD; Choy, KL
    Structural characterisation of thermal barrier coatings deposited using electrostatic spray assisted vapour deposition method
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
    
    J.D. Vyas e K.L. Choy, "Structural characterisation of thermal barrier coatings deposited using electrostatic spray assisted vapour deposition method", MAT SCI E A, 277(1-2), 2000, pp. 206-212
94. Griffin, GJ; Wood, DG
    Modelling of the catalytic combustion of lean fuel flowing over a fin withheat extraction from the trailing edge
    CATALYSIS TODAY
    
    G.J. Griffin e D.G. Wood, "Modelling of the catalytic combustion of lean fuel flowing over a fin withheat extraction from the trailing edge", CATAL TODAY, 63(2-4), 2000, pp. 387-395
95. Forzatti, P
    Environmental catalysis for stationary applications
    CATALYSIS TODAY
    
    P. Forzatti, "Environmental catalysis for stationary applications", CATAL TODAY, 62(1), 2000, pp. 51-65
96. Seo, YS; Cho, SJ; Kang, SK; Shin, HD
    Experimental and numerical studies on combustion characteristics of a catalytically stabilized combustor
    CATALYSIS TODAY
    
    Y.S. Seo et al., "Experimental and numerical studies on combustion characteristics of a catalytically stabilized combustor", CATAL TODAY, 59(1-2), 2000, pp. 75-86
97. Lietti, L; Cristiani, C; Groppi, G; Forzatti, P
    Preparation, characterization and reactivity of Me-hexaaluminate (Me=Mn, Co, Fe, Ni, Cr) catalysts in the catalytic combustion of NH3-containing gasified biomasses
    CATALYSIS TODAY
    
    L. Lietti et al., "Preparation, characterization and reactivity of Me-hexaaluminate (Me=Mn, Co, Fe, Ni, Cr) catalysts in the catalytic combustion of NH3-containing gasified biomasses", CATAL TODAY, 59(1-2), 2000, pp. 191-204
98. Ubertini, S; Desideri, U
    Flow development and turbulence length scales within an annular gas turbine exhaust diffuser
    EXPERIMENTAL THERMAL AND FLUID SCIENCE
    
    S. Ubertini e U. Desideri, "Flow development and turbulence length scales within an annular gas turbine exhaust diffuser", EXP THERM F, 22(1-2), 2000, pp. 55-70
99. Kayakol, N; Selcuk, N; Campbell, I; Gulder, OL
    Performance of discrete ordinates method in a gas turbine combustor simulator
    EXPERIMENTAL THERMAL AND FLUID SCIENCE
    
    N. Kayakol et al., "Performance of discrete ordinates method in a gas turbine combustor simulator", EXP THERM F, 21(1-3), 2000, pp. 134-141
100. Guo, SM; Lai, CC; Jones, TV; Oldfield, MLG; Lock, GD; Rawlinson, AJ
     Influence of surface roughness on heat transfer and effectiveness for a fully film cooled nozzle guide vane measured by wide band liquid crystals anddirect heat flux gages
     JOURNAL OF TURBOMACHINERY-TRANSACTIONS OF THE ASME
     
     S.M. Guo et al., "Influence of surface roughness on heat transfer and effectiveness for a fully film cooled nozzle guide vane measured by wide band liquid crystals anddirect heat flux gages", J TURBOMACH, 122(4), 2000, pp. 709-716